Run-time Error 339

"Component tab32x30.OCX, spr32x25.OCX, spr32x35.OCX (or a different .OCX file) or one of its dependencies not correctly registered"  "A file is missing or invalid"

Run-time error 3051... The Microsoft Jet database engine cannot open the file

Can happen when opening HydraLIST or Head Selector

50.00.14+

1. Import clash errors does not work. Display Units any

Inserting a pipe dimension (pipex) places it at the end of the pipe, including its center grip or not even on the pipe at all

See solution #3 if the PIPEX is not on the pipe

When starting the AutoLIST process, it sits there normally then you get this error message. 

You have canceled. There is nothing to stocklist

Fatal Error

Runtime error 70 permission denied

While using the 'Choose Part Number' button to open HydraHEAD Selector and retrieive its description and part number, you get the errors below;

Runtime Error 713, Application-defined or object-defined error

Sprinkler not properly configured.  Please re-select using 'Choose part'

Step 2.3 - After one pass through calculations Miscfunc hangs....

Also possibly "Hydraulic Engine not responding" and a "Runtime Error 62 input past end of file"

Step 1a.3 - Fitting Exchange No replacement fitting name for 22E for Sched-10 Note: This could be any fitting or pipe type described in the error. If you click ok at each error, the process will run through without these fittings

When opening HydraCAD, you only receive this error message and not a HydraKEY error with the golden X.  If you receive a HydraKEY error, search for the linked HydraCARD in that message box as it takes priority.

Security Error:  One of the following conditions is likely;

HydraCAD is unable to function under these conditions

• Lock database needs updating in HydraKEY
• Accounting flag on your account
• Hardware lock not plugged in
• Extra ACAD.RX file found in folder in Support File Search Path
• Sentinel driver is missing
• InstallPath registry item set to wrong drive

After AutoCAD opens, press F2 to view the command prompt, see if the text below appears.  If yes, see solution 1.

Could not find file HCAD_ENV.INI

Is 2024; error: no function definition: PRINTEM

Keyboard alias "BS"

Bayspace preview is not lining up the sprinklers evenly.  Or Bayspace stops working with a "Bad Argument Type 2D/3D point error." message.

Upon starting the Show 3D command (S3D) the drawing immediately switches to SE isometric, reports no errors but no 3D piping is visible.  Even newly drawn pipe won't elevate.

Drawing successfully elevated to 3D. No errors were found

Related HydraCARD: #853

https://hydracards.hydratecinc.com/cards/card-853

Unhandled exception: Input string not in correct format

Primary calc results are shown, and when selecting OK to continue back to the calc input screen, the two messages below are displayed, twice;

"The designated source node was not found in the list of pipes" OK

"Calculation failed for an unknown reason" OK

Process Error Hydcalc

Runtime Error 7 Out of memory run-time error 7 run time error 7 Runtime Error 7 Miscfunc

When opening HydraCALC, you get this error.

Startup error

An error has occured during startup. The decimal separator & digit grouping symbols are not set correctly in Control Panel! The digit grouping symbol must be a comma!

During the AutoCALC process, it gets hung up at step 5a.3b. 

Re-Ordering Pipe Paths - Phase 2

Step 5a.3 "Attaching Elevation of ~ to Node ~~~~

Step 5a.3 "Calculating"

"The specified remote node does not have a k-factor. Please fix your input."

"Calculation failed for unknown reason"

After calculating system this message pops up..."The specified remote head does not have a k factor. Please fix your input" hydcalc.exe